ESF-IDF is the Espressif Internet of Things (IOT) Development Framework. In 5.5.1, 5.4.3, 5.3.4, 5.2.6, 5.1.6, and earlier, when AVRCP is enabled on ESP32, receiving a malformed VENDOR DEPENDENT command from a peer device can cause the Bluetooth stack to access memory before validating the command buffer length. This may lead to an out-of-bounds read, potentially exposing unintended memory content or causing unexpected behavior.
ESF-IDF is the Espressif Internet of Things (IOT) Development Framework. In versions 5.5.1, 5.4.3, and 5.3.4, when the ESP32-P4 uses its hardware JPEG decoder, the software parser lacks necessary validation checks. A specially crafted (malicious) JPEG image could exploit the parsing routine and trigger an out-of-bounds array access. This issue has been fixed in versions 5.5.2, 5.4.4, and 5.3.5. At time of publication versions 5.5.2, 5.4.4, and 5.3.5 have not been released but are fixed respectively in commits 4b8f585, c79cb4d, and 34e2726.
ESF-IDF is the Espressif Internet of Things (IOT) Development Framework. When the ESP32 is in advertising mode, if it receives a connection request containing an invalid Access Address (AA) of 0x00000000 or 0xFFFFFFFF, advertising may stop unexpectedly. In this case, the controller may incorrectly report a connection event to the host, which can cause the application layer to assume that the device has successfully established a connection. This issue has been fixed in versions 5.5.2, 5.4.3, 5.3.5, 5.2.6, and 5.1.7. At time of publication versions 5.5.2, 5.3.5, and 5.1.7 have not been released but are fixed respectively in commits 3b95b50, e3d7042, and 75967b5.
ESF-IDF is the Espressif Internet of Things (IOT) Development Framework. The BluFi example bundled in ESP-IDF was vulnerable to memory overflows in two areas: Wi-Fi credential handling and Diffie–Hellman key exchange. This vulnerability is fixed in 5.4.1, 5.3.3, 5.1.6, and 5.0.9.
arduino-esp32 is an Arduino core for the ESP32, ESP32-S2, ESP32-S3, ESP32-C3, ESP32-C6 and ESP32-H2 microcontrollers. Several OTA update examples and the HTTPUpdateServer implementation are vulnerable to Cross-Site Request Forgery (CSRF). The update endpoints accept POST requests for firmware uploads without CSRF protection. This allows an attacker to upload and execute arbitrary firmware, resulting in remote code execution (RCE). This vulnerability is fixed in 3.2.1.
arduino-esp32 provides an Arduino core for the ESP32. Versions prior to 3.3.0-RC1 and 3.2.1 contain a HTTP Response Splitting vulnerability. The `sendHeader` function takes arbitrary input for the HTTP header name and value, concatenates them into an HTTP header line, and appends this to the outgoing HTTP response headers. There is no validation or sanitization of the `name` or `value` parameters before they are included in the HTTP response. If an attacker can control the input to `sendHeader` (either directly or indirectly), they could inject carriage return (`\r`) or line feed (`\n`) characters into either the header name or value. This could allow the attacker to inject additional headers, manipulate the structure of the HTTP response, potentially inject an entire new HTTP response (HTTP Response Splitting), and/or ause header confusion or other HTTP protocol attacks. Versions 3.3.0-RC1 and 3.2.1 contain a fix for the issue.
ESF-IDF is the Espressif Internet of Things (IOT) Development Framework. An integer underflow vulnerability has been identified in the ESP-NOW protocol implementation within the ESP Wi-Fi component of versions 5.4.1, 5.3.3, 5.2.5, and 5.1.6 of the ESP-IDF framework. This issue stems from insufficient validation of user-supplied data length in the packet receive function. Under certain conditions, this may lead to out-of-bounds memory access and may allow arbitrary memory write operations. On systems without a memory protection scheme, this behavior could potentially be used to achieve remote code execution (RCE) on the target device. In versions 5.4.2, 5.3.4, 5.2.6, and 5.1.6, ESP-NOW has added more comprehensive validation logic on user-supplied data length during packet reception to prevent integer underflow caused by negative value calculations. For ESP-IDF v5.3 and earlier, a workaround can be applied by validating that the `data_len` parameter received in the RX callback (registered via `esp_now_register_recv_cb()`) is a positive value before further processing. For ESP-IDF v5.4 and later, no application-level workaround is available. Users are advised to upgrade to a patched version of ESP-IDF to take advantage of the built-in mitigation.