In the Linux kernel, the following vulnerability has been resolved: wifi: mwifiex: bound uAP association event IEs to the event buffer mwifiex_process_uap_event() handles EVENT_UAP_STA_ASSOC by exposing the (re)association request IEs that the firmware copies into the event: sinfo->assoc_req_ies = &event->data[len]; len = (u8 *)sinfo->assoc_req_ies - (u8 *)&event->frame_control; sinfo->assoc_req_ies_len = le16_to_cpu(event->len) - (u16)len; event->len is supplied by the device firmware and is never validated, and the subtraction is unchecked. assoc_req_ies points into adapter->event_body[MAX_EVENT_SIZE], a fixed-size array embedded in the kmalloc()'d struct mwifiex_adapter. On the ap_11n_enabled path mwifiex_set_sta_ht_cap() walks these IEs with cfg80211_find_ie(), whose for_each_element() loop dereferences each element header. A firmware-reported event->len larger than the bytes actually received makes assoc_req_ies_len describe IEs that extend past event_body, so the walk reads out of the adapter slab object, a slab-out-of-bounds read (KASAN: slab-out-of-bounds in cfg80211_find_ie). An event->len smaller than the header instead makes the int subtraction negative, which wraps to a huge size_t when stored in assoc_req_ies_len. The same length is handed to cfg80211_new_sta(), so a more modest over-claim can also copy stale event_body bytes into the NL80211_CMD_NEW_STATION notification. A malicious or malfunctioning mwifiex device (USB/SDIO/PCIe) can deliver such an event while the interface is in AP/uAP mode. Validate event->len before use: reject a length that underflows the header or that would place the IEs outside the event_body[] buffer the event was copied into. event->len here is struct mwifiex_assoc_event.len, a payload field internal to this event, not the transport frame length, so it is validated in this handler rather than at the generic MWIFIEX_TYPE_EVENT receive path, which only sees the event cause and the transport frame length. The bound is against event_body[MAX_EVENT_SIZE] rather than the actually-received length because the transports store the event differently (USB and SDIO leave the 4-byte event header in event_skb, PCIe strips it via skb_pull), whereas event_body is the single fixed buffer all of them copy the event into. This is the event-path analogue of the receive-path bounds checks added in commit 119585281617 ("wifi: mwifiex: Fix OOB and integer underflow when rx packets").
In the Linux kernel, the following vulnerability has been resolved: wifi: carl9170: fix buffer overflow in rx_stream failover path The failover continuation in carl9170_rx_stream() copies the full tlen from the second USB transfer instead of capping at rx_failover_missing bytes. When both transfers are near maximum size, the total exceeds the 65535-byte failover SKB, triggering skb_over_panic. Limit the copy size to the missing byte count. [Fix checkpatch CHECK:PARENTHESIS_ALIGNMENT]
In the Linux kernel, the following vulnerability has been resolved: wifi: ath6kl: fix OOB read from firmware IE lengths in connect event The firmware-controlled beacon_ie_len, assoc_req_len, and assoc_resp_len fields in ath6kl_wmi_connect_event_rx() are not validated against the buffer length. Their sum (up to 765) can exceed the actual WMI event data, causing out-of-bounds reads during IE parsing and state corruption of wmi->is_wmm_enabled. Add a check that the total IE length fits within the buffer.
In the Linux kernel, the following vulnerability has been resolved: wifi: ath6kl: fix OOB read from firmware num_msg in TX complete handler The firmware-controlled num_msg field (u8, 0-255) drives the loop in ath6kl_wmi_tx_complete_event_rx() without validation against the buffer length. This allows out-of-bounds reads of up to 1020 bytes past the WMI event buffer when the firmware sends an inflated num_msg. Add a check that the buffer is large enough to hold the fixed struct and the num_msg variable-length entries.
In the Linux kernel, the following vulnerability has been resolved: wifi: at76c50x-usb: avoid length underflow in at76_guess_freq() at76_guess_freq() checks only that the received frame is at least a bare 802.11 header (24 bytes) before subtracting the fixed management-body offset: len -= el_off; For both beacon and probe response frames, el_off is 36. If the frame is shorter than el_off, subtracting it causes the calculated IE length to wrap. The length is eventually passed to cfg80211_find_elem_match() as a very large unsigned value, so the element walk runs beyond the RX skb. This path is reached from at76_rx_tasklet() while scanning. If the device delivers a truncated beacon or probe response, the oversized IE length causes an out-of-bounds read during scanning. Skip the IE lookup if the frame does not reach the variable elements, before subtracting el_off.
In the Linux kernel, the following vulnerability has been resolved: mptcp: fix stale skb->sk reference on subflow close The backlog list is updated by mptcp_data_ready() under mptcp_data_lock(). The cleanup of backlog references to a closing subflow, however, was performed in mptcp_close_ssk(), before __mptcp_close_ssk() acquires the ssk lock, and while holding neither the ssk lock nor mptcp_data_lock(). Because that traversal ran without mptcp_data_lock(), concurrent softirq RX processing on another CPU (subflow_data_ready() -> mptcp_data_ready() -> __mptcp_add_backlog(), under mptcp_data_lock()) could add a backlog entry referencing the ssk while the cleanup loop was in progress. Such an entry could be missed by the cleanup, or the concurrent list update could corrupt the traversal, leaving skb->sk pointing at the ssk after it is freed. A later mptcp_backlog_purge() then dereferences the stale pointer, triggering a warning in inet_sock_destruct() (ssk->sk_rmem_alloc != 0) followed by a use-after-free in mptcp_backlog_purge(). Fix this by moving the backlog cleanup into __mptcp_close_ssk(), after subflow->closing is set to 1 and while the ssk lock is still held, serialized under mptcp_data_lock(). The cleanup runs only on the push path (MPTCP_CF_PUSH), where backlog references accumulate; on other teardown paths the caller already handles cleanup. With subflow->closing set and mptcp_data_lock() held across the purge, any concurrent mptcp_data_ready() either completes its enqueue before the purge runs and is caught, or observes closing=1 and bails out. Once mptcp_data_unlock() is reached, no new skb referencing the ssk can be enqueued, so the cleanup is exhaustive. Remove the unprotected traversal from mptcp_close_ssk() entirely.
In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: mt7925: drop TXRX_NOTIFY on non-mmio buses PKT_TYPE_TXRX_NOTIFY is an mmio-only event, but mt7925_rx_check() and mt7925_queue_rx_skb() dispatch it to mt7925_mac_tx_free() on every bus. mt7925_mac_tx_free() cleans the DMA tx queues with mt76_queue_tx_cleanup(), which calls queue_ops->tx_cleanup(). Only the mmio queue ops implement that callback; on USB it is NULL, so a TXRX_NOTIFY there calls a NULL pointer in the RX worker: BUG: kernel NULL pointer dereference, address: 0000000000000000 RIP: 0010:0x0 Call Trace: mt7925_mac_tx_free+0x58/0x350 [mt7925_common] mt7925_rx_check+0xe2/0x130 [mt7925_common] mt76u_rx_worker+0x1b9/0x620 [mt76_usb] Drop the event on non-mmio buses via mt76_is_mmio(), as in commit 5683e1488aa9 ("wifi: mt76: connac: do not check WED status for non-mmio devices").
In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: mt7921: drop TXRX_NOTIFY on non-mmio buses PKT_TYPE_TXRX_NOTIFY is an mmio-only event, but mt7921_rx_check() and mt7921_queue_rx_skb() dispatch it to mt7921_mac_tx_free() on every bus. mt7921_mac_tx_free() cleans the DMA tx queues with mt76_queue_tx_cleanup(), which calls queue_ops->tx_cleanup(). Only the mmio queue ops implement that callback; on USB and SDIO it is NULL, so a TXRX_NOTIFY there calls a NULL pointer in the RX worker: BUG: kernel NULL pointer dereference, address: 0000000000000000 RIP: 0010:0x0 Call Trace: mt7921_mac_tx_free+0x64/0x310 [mt7921_common] mt7921_rx_check+0x5f/0xf0 [mt7921_common] mt76u_rx_worker+0x1b9/0x620 [mt76_usb] Drop the event on non-mmio buses via mt76_is_mmio(), as in commit 5683e1488aa9 ("wifi: mt76: connac: do not check WED status for non-mmio devices").
In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: mt7615: drop TXRX_NOTIFY on non-mmio buses PKT_TYPE_TXRX_NOTIFY is an mmio-only event, but mt7615_rx_check() and mt7615_queue_rx_skb() dispatch it to mt7615_mac_tx_free() on every bus. mt7615_mac_tx_free() cleans the DMA tx queues with mt76_queue_tx_cleanup(), which calls queue_ops->tx_cleanup(). Only the mmio queue ops implement that callback; on the mt7663 USB and SDIO buses it is NULL, so a TXRX_NOTIFY there calls a NULL pointer in the RX worker. Same defect as the mt7921 and mt7925 patches in this series. Drop the event on non-mmio buses via mt76_is_mmio(), as in commit 5683e1488aa9 ("wifi: mt76: connac: do not check WED status for non-mmio devices").
In the Linux kernel, the following vulnerability has been resolved: net: hsr: fix memory leak on slave unregistration by removing synced VLANs When an HSR master device is brought UP, it auto-adds VLAN 0 via vlan_vid0_add(), which propagates VID 0 to its slave devices (slave A and B). If a slave device is later unregistered while HSR is active (e.g., during netns cleanup or interface destruction), hsr_del_port() is called to detach the slave port from the HSR master. However, hsr_del_port() currently does not delete the VLAN IDs that were synced to the slave device by HSR. As a result, the slave device retains a refcount on VID 0 (and any other synced VLANs). When the slave device is destroyed, its vlan_info / vlan_vid_info structure remains allocated, leading to a memory leak. Fix this by calling vlan_vids_del_by_dev(port->dev, master->dev) in hsr_del_port() before unlinking slave A or slave B ports, matching the propagation logic in hsr_ndo_vlan_rx_add_vid() / hsr_ndo_vlan_rx_kill_vid() and the cleanup behavior in bonding and team drivers.
In the Linux kernel, the following vulnerability has been resolved: rxrpc: fix io_thread race in rxrpc_wake_up_io_thread() rxrpc_wake_up_io_thread() checks local->io_thread before waking it, but then reloads the pointer for wake_up_process(). local->io_thread is cleared with WRITE_ONCE() when the I/O thread exits, so the second load can see NULL even if the first load did not. Take a READ_ONCE() snapshot and use it for both the NULL check and the wake_up_process() call, as rxrpc_encap_rcv() already does.
In the Linux kernel, the following vulnerability has been resolved: wifi: ath11k: fix potential buffer underflow in ath11k_hal_rx_msdu_list_get() When the first entry in msdu_details has a zero buffer address, the code accesses msdu_details[i - 1] with i == 0, causing a buffer underflow. Fix similarly to ath12k_wifi7_hal_rx_msdu_list_get() by adding a separate check for i == 0 before the main condition to prevent the out-of-bounds access. Found by Linux Verification Center (linuxtesting.org) with SVACE.
In the Linux kernel, the following vulnerability has been resolved: usb: gadget: printer: fix infinite loop in printer_read() printer_read() uses the same variable for the requested copy size and the number of bytes actually copied to user space. copy_to_user() returns the number of bytes not copied, so when it fails to copy anything, the computed copied length becomes zero. In that case len, buf, current_rx_bytes and current_rx_buf are left unchanged. If RX data is available and the user buffer remains unwritable, the read loop can repeat indefinitely. Track the copied length separately and return -EFAULT, or the number of bytes already copied, if an iteration makes no progress.
In the Linux kernel, the following vulnerability has been resolved: ppp: defer channel free to an RCU grace period to fix pppol2tp RX UAF pppol2tp_recv() runs in the L2TP UDP-encap softirq RX path: l2tp_udp_encap_recv() -> l2tp_recv_common() -> pppol2tp_recv() -> ppp_input(&po->chan) It runs under rcu_read_lock() holding only an l2tp_session reference and takes NO reference on the internal PPP channel (struct channel, chan->ppp) that ppp_input() dereferences. The pppox socket is SOCK_RCU_FREE, so 'po' and the embedded ppp_channel are RCU-safe. But the internal struct channel is a separate allocation that ppp_release_channel() frees with a plain kfree(): close(data socket) -> pppol2tp_release() -> pppox_unbind_sock() -> ppp_unregister_channel() -> ppp_release_channel() -> kfree(pch) For a channel that is bound (PPPIOCGCHAN) but not attached to a ppp unit (no PPPIOCCONNECT, pch->ppp == NULL) and not bridged, teardown skips both ppp_disconnect_channel()'s synchronize_net() and ppp_unbridge_channels()'s synchronize_rcu(), so the kfree() has no grace period. rcu_read_lock() in pppol2tp_recv() does not protect against a plain kfree(), so an in-flight ppp_input() on one CPU can dereference the channel just freed by close() on another CPU. The bug is reachable by an unprivileged user. Defer the channel free to an RCU callback via call_rcu() so the grace period fences any in-flight ppp_input(). The disconnect and unbridge teardown paths already fence with synchronize_net()/synchronize_rcu(); call_rcu() does the same here without stalling the close() path.
In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: defer link RX stats percpu free to RCU sta_remove_link() frees a removed MLO link's RX stats percpu buffer right away, but defers only the link container to RCU: sta_info_free_link(&alloc->info); kfree_rcu(alloc, rcu_head); The RX fast path reads link_sta under rcu_read_lock and writes the percpu stats. A reader that resolved link_sta before the removal keeps the pointer. The container stays alive from the kfree_rcu, so the read still works. But the percpu block it points to is already freed. This needs uses_rss. That is when pcpu_rx_stats exists. The full STA teardown frees the deflink stats only after synchronize_net(). The link removal path had no such barrier. The race is hard to win in practice, but the free should still wait for RCU. Free the link together with its data from a single RCU callback, so the percpu block is reclaimed only after readers drain.
In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211_hwsim: clamp virtio RX length before skb_put hwsim_virtio_rx_work() passes the virtqueue used-ring length reported by the device straight to skb_put() on a fixed-size receive skb. A backend reporting a length larger than the skb tailroom drives skb_put() past the buffer end and hits skb_over_panic() -- a host-triggerable guest panic (denial of service). Clamp the length to the skb's available room before skb_put(). A conforming device never reports more than the posted buffer size, so valid frames are unaffected; a truncated over-report then fails the length/header checks in hwsim_virtio_handle_cmd() and is dropped, so truncating rather than dropping here cannot be turned into a parsing problem.
In the Linux kernel, the following vulnerability has been resolved: ovpn: fix peer refcount leak in TCP error paths When either the TCP RX or TX error path calls ovpn_peer_hold() followed by schedule_work(&peer->tcp.defer_del_work), and the work item is already pending from the other path, schedule_work() returns false and the work runs only once. Since ovpn_tcp_peer_del_work() calls ovpn_peer_put() exactly once, the extra reference taken by the losing path is never dropped, leaking the peer object. The race window: CPU0 (strparser/RX error): CPU1 (tcp_tx_work/TX error): ovpn_peer_hold() <- refcnt+1 ovpn_peer_hold() <- refcnt+2 schedule_work() <- queued schedule_work() <- NO-OP (work already pending) ovpn_tcp_peer_del_work runs: ovpn_peer_del() ovpn_peer_put() <- refcnt+1 <- peer never freed Fix by checking the return value of schedule_work() in both paths and calling ovpn_peer_put() to drop the extra reference if the work was already pending. ovpn_peer_hold() is kept unconditional in the TX path as it cannot fail at that point.
In the Linux kernel, the following vulnerability has been resolved: mctp: serial: handle zero-length frames to prevent rx buffer overflow The MCTP serial receive state machine reads a frame length byte in mctp_serial_push_header() case 2 and validates it upper-bound-only: if (c > MCTP_SERIAL_FRAME_MTU) { dev->rxstate = STATE_ERR; } else { dev->rxlen = c; dev->rxpos = 0; dev->rxstate = STATE_DATA; ... } A length of zero passes this check, so rxlen is set to 0 and the state machine advances to STATE_DATA. In mctp_serial_push() STATE_DATA, the incoming byte is stored and rxpos incremented before the terminator is dev->rxbuf[dev->rxpos] = c; dev->rxpos++; dev->rxstate = STATE_DATA; if (dev->rxpos == dev->rxlen) { dev->rxpos = 0; dev->rxstate = STATE_TRAILER; } With rxlen == 0 the "rxpos == rxlen" terminator can never fire (rxpos is already 1 on the first data byte), so subsequent bytes are written past the end of the fixed 74-byte rxbuf, which is the last member of the netdev private area. Every following data byte is an attacker-controlled 1-byte out-of-bounds heap write, and the overflow continues until a frame (0x7e) or escape byte resets the parser -- effectively unbounded. Reaching this requires CAP_NET_ADMIN to attach the N_MCTP line discipline and bring the resulting mctpserialN netdev up, after which the bytes arrive via the tty receive path. Route a zero-length frame straight to STATE_TRAILER instead of STATE_DATA. The trailer/framing bytes are still consumed, and the frame resolves to a zero-length skb that the MCTP core rejects; the parser never enters STATE_DATA with rxlen == 0, so the out-of-bounds write can no longer occur. KASAN, on a frame of 0x7e 0x01 0x00 followed by data bytes (before this change): UBSAN: array-index-out-of-bounds in drivers/net/mctp/mctp-serial.c:370 index 74 is out of range for type 'u8 [74]' BUG: KASAN: slab-out-of-bounds in mctp_serial_tty_receive_buf Write of size 1 at addr ... by task kworker/u16:0 mctp_serial_tty_receive_buf tty_ldisc_receive_buf flush_to_ldisc Allocated by task 152: alloc_netdev_mqs mctp_serial_open v2: route zero-length frames to STATE_TRAILER instead of STATE_ERR so the trailer/framing bytes are still consumed (Jeremy Kerr). Found by 0sec automated security-research tooling (https://0sec.ai).
In the Linux kernel, the following vulnerability has been resolved: gve: fix Rx queue stall on alloc failure When the system is under extreme memory pressure, page allocations can fail during the Rx buffer refill loop. If the number of buffers posted to hardware falls below a critical low threshold and the refill loop exits due to allocation failures, the queue can stall: 1. The device drops incoming packets because there are no descriptors. 2. Since no packets are processed, no Rx completions are generated. 3. Because no completions occur, NAPI is never scheduled, preventing the refill loop from running again even after memory is freed. This results in a permanent queue stall. Resolve this by introducing a starvation recovery timer for each Rx queue. If the number of buffers posted to hardware falls below a critical low threshold, start a timer to periodically reschedule NAPI. Once NAPI runs and successfully refills the queue above the threshold, the timer is not rescheduled. The threshold is set to 32 because a single maximum-sized Receive Segment Coalescing (RSC) packet can consume up to 19 descriptors in the Rx path. Lower thresholds (such as 8 or 16) would be insufficient to process a complete maximum-sized RSC packet, risking packet drops or unexpected hardware behavior under memory pressure. Setting the threshold to 32 guarantees a safe margin to handle at least one full RSC packet.
In the Linux kernel, the following vulnerability has been resolved: net: hip04: fix RX buffer leak on build_skb failure When build_skb() fails in hip04_rx_poll(), the driver jumps to the refill path without releasing the current RX buffer and its DMA mapping. Installing a replacement buffer then overwrites the slot references and leaks both resources. Keep the current slot intact and return budget so NAPI retries the same buffer. Also free a newly allocated RX fragment when dma_map_single() fails. This issue was found by an in-house static analysis tool.