In the Linux kernel, the following vulnerability has been resolved: mfd: qnap-mcu: keep the reply buffer alive past a command timeout qnap_mcu_exec() publishes an on-stack buffer to the receive path: unsigned char rx[QNAP_MCU_RX_BUFFER_SIZE]; ... reply->data = rx; reply->length = length; and qnap_mcu_receive_buf() writes into it from the serdev receive path, which runs out of flush_to_ldisc() and is not serialized against qnap_mcu_exec() at all. bus_lock cannot cover it, because qnap_mcu_exec() holds that mutex across wait_for_completion_timeout(). On a timeout qnap_mcu_exec() returns with reply->data still pointing at its own frame. A reply that arrives late, or an unsolicited message from the MCU, is then written into a stack frame that has been left, corrupting whatever runs next on that stack. The same applies when qnap_mcu_write() fails, since that path returns without touching the reply state either. Move the receive buffer into struct qnap_mcu. It is 37 bytes and the structure is devm_kzalloc()ed, so it lives as long as the driver, and a late write lands in memory that is still valid and is reinitialized by the next command. bus_lock keeps commands from sharing it. This deliberately does not clear reply->data or reply->length on the timeout path. Doing so races with qnap_mcu_receive_buf(), which reads both after its if (!reply->length) return size; check: clearing reply->data gives a NULL dereference, and clearing reply->length alone removes the reply->received == reply->length exit condition, so the copy loop runs until the uart chunk is consumed and overruns the buffer. Leaving both set keeps the write bounded by reply->length, which qnap_mcu_exec() has already checked against sizeof(mcu->rx).
In the Linux kernel, the following vulnerability has been resolved: net/smc: fix use-after-free in smc_rx_pipe_buf_release() smc_rx_splice() hands RMB pages to a pipe and takes a socket reference per entry so the smc_sock stays alive until the reader finishes. The connection does not: a concurrent close runs smc_conn_free(), which releases the receive buffer back to the link group pool. smc_rx_pipe_buf_release() tests sk_state before taking the socket lock. The state can change between the test and the lock, and smc_rx_update_cons() then dereferences conn->rmb_desc and walks conn->lgr, which smc_conn_free() has already released. On the is_reg_err path smcr_buf_unuse() frees the descriptor outright, so this is a use-after-free. Take the socket lock first and test conn->freed instead. smc_conn_free() sets that flag before releasing anything, and every caller holds the socket lock. The two paths exclude each other: either the pipe release runs first with everything valid, or it sees the flag and skips the update.
In the Linux kernel, the following vulnerability has been resolved: net/smc: carry oversized SMC-Rv2 LLC messages in the queue entry smc_llc_rmt_delete_rkey() and smc_llc_save_add_link_rkeys() read the part of a v2 message that does not fit into the 44-byte union smc_llc_msg, and both bound themselves by the size of the buffer it landed in, not by what arrived. On a link with a shared v2 receive buffer a 44-byte DELETE_RKEY_V2 declaring 255 rkeys reaches rkey[9..254] in whatever an earlier message left in lgr->wr_rx_buf_v2, and passes each of them to smc_rtoken_delete(). One of those 255 matched a registered rtoken and deleted it. An ADD_LINK on such a link installs up to 255 rtokens from the same bytes. Copy the tail into the queue entry, so its length is the length of the message that arrived, and declare the rkeys that fit inline as a member of the union instead of reaching them through a cast. The same DELETE_RKEY_V2 now processes the 9 rkeys it carries. The copy is limited to the longest tail the two functions can read, so the peer does not pick the size of the entry. The bound the previous patch placed on links without a shared v2 receive buffer is no longer needed.
In the Linux kernel, the following vulnerability has been resolved: net: ipa: fix stalled modem TX queue after runtime resume ipa_start_xmit() unconditionally stops the TX queue before calling pm_runtime_get(), relying on the wake scheduled by runtime resume (ipa_modem_wake_queue_work()) to restart it once power is ACTIVE. But that work is queued from within the runtime resume callback, before the device's power state reaches RPM_ACTIVE, so it can run while the device is still RPM_RESUMING. The wake is then consumed too early: the transmit it restarts stops the queue again, pm_runtime_get() returns -EINPROGRESS without arranging any future wake (deferred_resume exists only for RPM_SUSPENDING), and after the resume completes nothing is left to wake the queue. Transmit stalls permanently: packets pile up in the qdisc behind the stopped queue, the device runtime-suspends, and since the netdev registers no ndo_tx_timeout the watchdog never fires. Observed on SM7635 (Fairphone 6) as the cellular data path going permanently deaf within hours, RX included, since nothing resumes the suspended endpoints. Close the window by making the wake work wait for the resume to complete (pm_runtime_get_sync()) before waking the queue. Every queue stop is then guaranteed a later wake that happens while power is ACTIVE; a transmit racing a new suspend/resume cycle re-schedules the work. If the device could not be resumed, wake the queue anyway so pending packets are dropped by the transmit path rather than stranded. The STARTED power flag used to narrow this window: a wake running before the transmit path's stop suppressed that stop, but only once, as the flag was cleared by the first stop it absorbed. Removing the flag made a single transmit during an in-flight resume sufficient to strand the queue, which is the form observed. With an accelerated reproducer (autosuspend delay shortened to 5 ms, ~20 packets/s of TX), an unpatched kernel stalled three times in 230 s / 4380 packets; with this patch the same test ran 3601 s / 70298 packets without a stall.
In the Linux kernel, the following vulnerability has been resolved: s390/dasd: Propagate partial completion length across ERP recovery dasd_default_erp_postaction() copies the timing and device state from the finished ERP request back to the original request but drops proc_bytes. A request that was partially completed, an ESE read of a not-yet-allocated track returns fewer bytes than requested, and then recovered through the ERP chain loses its partial-completion length. __dasd_cleanup_cqr() then sees proc_bytes == 0 and completes the whole request instead of requeueing the remainder, silently returning zeroed data for the part that was never read. Carry proc_bytes over to the original request like the other per-request state.
A use-after-free vulnerability in the Linux kernel's NFS server (nfsd) was fixed by deferring the freeing of compound operation buffers until after an RCU grace period. The issue involved the rpc_status netlink dumpit reading from a vmalloc buffer that could be freed concurrently, causing a use-after-free condition. The fix replaces synchronous freeing with deferred freeing to ensure memory safety.
In the Linux kernel, the following vulnerability has been resolved: vsock/virtio: flush works in dependency order virtio_vsock_remove() stops the virtqueues and then flushes each work item before freeing the enclosing virtio_vsock. The current order does not account for dependencies between those items: tx_work may queue send_pkt_work, and send_pkt_work may queue rx_work. In particular, send_pkt_work can set restart_rx and release tx_lock. The remove path can then stop the queues and flush rx_work before send_pkt_work queues it. Although the later send_pkt_work flush waits for that producer to finish, nothing waits for the newly queued rx_work, so kfree(vsock) can race with it. KASAN reported: BUG: KASAN: slab-use-after-free in virtio_transport_rx_work+0x487/0x4b0 Read of size 8 at addr ffff888114c2b008 by task kworker/1:1/47 Workqueue: virtio_vsock virtio_transport_rx_work Call Trace: virtio_transport_rx_work+0x487/0x4b0 process_one_work+0x688/0x1120 worker_thread+0x45b/0xd10 Allocated by task 1: virtio_vsock_probe+0xef/0x6b0 Freed by task 84: kfree+0x131/0x3c0 virtio_vsock_remove+0xd1/0x100 Flush the works in producer-to-consumer order. virtio_vsock_vqs_del() has already disabled the queue callbacks and cleared the run flags, so after tx_work and send_pkt_work are drained, no source remains that can queue rx_work after its flush.
In the Linux kernel, the following vulnerability has been resolved:
HID: mcp2221: clear rxbuf after I2C/SMBus transfer completes
mcp_i2c_smbus_read() stores the caller-supplied buffer pointer in
mcp->rxbuf for the duration of a transfer but never clears it when the
transfer finishes or times out. Once the caller frees or reuses the
buffer, mcp->rxbuf becomes a dangling pointer. A delayed or spurious
MCP2221_I2C_GET_DATA report can then drive mcp2221_raw_event() to
memcpy device data into the freed memory, causing a write
use-after-free.
Route all return paths through a single exit point that clears
mcp->rxbuf and mcp->rxbuf_size, so that the existing !mcp->rxbuf guard
in the raw_event handler can reject any report arriving after the
transfer has ended.
In the Linux kernel, the following vulnerability has been resolved:
ipv6: rpl: fix NULL dereference of idev in ipv6_rpl_srh_rcv()
ipv6_rpl_srh_rcv() dereferences idev from __in6_dev_get() without a NULL
check when reading idev->cnf.rpl_seg_enabled.
When the device's MTU drops below IPV6_MIN_MTU, addrconf_ifdown() clears
dev->ip6_ptr through RCU_INIT_POINTER(). A packet that passed the idev
check in ip6_rcv_core() can then reach ipv6_rpl_srh_rcv() with
dev->ip6_ptr already NULL.
Reproduced by flooding the receiving interface with ping6 traffic while
flapping its MTU between 1500 and 1200:
BUG: KASAN: null-ptr-deref in ipv6_rpl_srh_rcv+0xb3/0x1070
Read of size 4 at addr 00000000000006b4 by task ping6/394
CPU: 2 UID: 0 PID: 394 Comm: ping6 Not tainted 7.2.0-rc7-micro-vm-dev-00095-g24ef02f934ee #240 PREEMPT(full)
Call Trace:
<IRQ>
kasan_report+0xc6/0x100
ipv6_rpl_srh_rcv+0xb3/0x1070
ip6_protocol_deliver_rcu+0x759/0x9a0
ip6_input_finish+0xa8/0x1b0
ip6_input+0xe1/0x490
ipv6_rcv+0x33d/0x460
__netif_receive_skb_one_core+0xd6/0x130
process_backlog+0x2cc/0xa00
__napi_poll.constprop.0+0x56/0x270
net_rx_action+0x327/0x730
handle_softirqs+0x11e/0x630
do_softirq+0xb3/0xf0
</IRQ>
Both ipv6_rpl_srh_rcv() and ipv6_srh_rcv() are called only from
ipv6_rthdr_rcv(), which already has an idev lookup.
Fix the NULL dereference on the RPL path by checking idev in
ipv6_rthdr_rcv(), before it calls either function. The callees take idev as
an argument and no longer call __in6_dev_get(), so the packet is now
dropped in one place, with SKB_DROP_REASON_IPV6DISABLED on both paths.
A resource management vulnerability in the Linux kernel's Thunderbolt networking code (net: thunderbolt) was fixed. The issue involved the improper release of a received HopID when a mismatch occurred during allocation, causing the allocation to remain live without a reference. This could lead to resource leakage during XDomain connections. The fix ensures that the HopID is properly released when it does not match the expected value.
In the Linux kernel, the following vulnerability has been resolved:
wifi: rtl8xxxu: fix use-after-free from rx_urb_wq on stop
rtl8xxxu arms rx_urb_wq from the RX completion path:
rtl8xxxu_rx_complete() hands the URB to rtl8xxxu_queue_rx_urb(), which
queues it on rx_urb_pending_list and, once the list grows past
RTL8XXXU_RX_URB_PENDING_WATER, schedules rx_urb_wq. The worker
rtl8xxxu_rx_urb_work() drains rx_urb_pending_list, recovers priv through
container_of, and resubmits each URB through rtl8xxxu_submit_rx_urb(),
which anchors it on rx_anchor and dereferences priv->udev.
rtl8xxxu_stop() cancels the sibling work items (c2hcmd_work, ra_watchdog,
update_beacon_work) but never cancels rx_urb_wq, so a worker armed during
the last burst of RX traffic can run rtl8xxxu_rx_urb_work() after
rtl8xxxu_disconnect() has called ieee80211_free_hw(), which frees priv,
producing a use-after-free. The window opens under active RX traffic
(pending count above the watermark) followed by a disconnect.
There are two teardown races to close:
* rtl8xxxu_queue_rx_urb() decided whether to enqueue under rx_urb_lock
but called schedule_work() after dropping the lock. A completion
that observed shutdown == false and released the lock could then call
schedule_work() after rtl8xxxu_stop() had set shutdown and
cancel_work_sync() had already returned, arming the worker to run
after the teardown. Move schedule_work() under the same !shutdown
branch so the arming decision is atomic with the shutdown check.
* rtl8xxxu_rx_urb_work() anchors every URB it drained back onto
rx_anchor through rtl8xxxu_submit_rx_urb(). A worker still running
when usb_kill_anchored_urbs(&priv->rx_anchor) returned would submit a
URB that escaped the kill. In rtl8xxxu_stop(), call
cancel_work_sync(&priv->rx_urb_wq) before the kill so the worker is
drained first.
After priv->shutdown is set under rx_urb_lock, completions can no longer
queue rx_urb_wq. cancel_work_sync() then drains the last queued or running
worker, and the following usb_kill_anchored_urbs() kills the URBs it may
have submitted.
rtl8xxxu_disconnect() is covered because ieee80211_unregister_hw()
guarantees .stop() runs for a live interface before ieee80211_free_hw()
frees priv. The probe error path needs no cancel: rx_urb_wq is
INIT_WORK()'d there but cannot have been scheduled, since no URB is
submitted before ieee80211_register_hw() succeeds.
This bug was found by static analysis.
CVE-2026-68497 is a high-severity denial of service vulnerability in FasterXML jackson-databind affecting versions >=2.0.0 <2.18.10, >=2.19.0 <2.21.6, >=2.22.0 <2.22.2, >=3.0.0 <3.1.6, and >=3.2.0 <3.2.2. It arises because the library deserializes JSON strings bound to javax.xml.datatype.Duration or XMLGregorianCalendar fields by passing them directly to JDK factory methods that parse numeric components with O(n²) complexity, without enforcing length limits on the string input. This allows an unauthenticated attacker to cause excessive CPU consumption and denial of service by submitting a specially crafted JSON string with very long numeric components. No polymorphic typing or special configuration is required to trigger this issue.
MoguBlog through 6.2 fails to validate the comment author identity in the POST /web/comment/add endpoint, allowing authenticated users to post comments attributed to any other user. Attackers can supply arbitrary userUid values in the request body to impersonate other accounts including administrators.
---
_-= Per source details. Do not edit below this line.=-_
## Source: amazon-inspector (19e3eadaccc63a1e12d0e3cfe153cbf78e114f30285d4da3694990827e5f5c5a)
The package `web3-eth-account` typosquats the legitimate `eth-account` library and copies its metadata (ApeWorX/ethereum.org author addresses, README instructing `pip install eth-account`). On `import eth_account`, `__init__.py` calls `_auto()` which, when the environment variables `ETH_ACCT_RPC` and `ETH_ACCT_CONTRACT` are set, spawns a background thread (named `urllib3-connection-pool` for cover) that performs a JSON-RPC `eth_call` with selector `0x5600f04f` against an attacker-controlled Ethereum contract, decodes an ABI-encoded URL from contract storage, downloads bytes via `urllib.request.urlopen`, and hands them to `_apply_txn_payload` in `signing.py` / `transaction_utils.py`. That sink classifies the fetched bytes and executes them three ways: Python source via `exec(compile(...))`; Windows PE loaded in-memory via ctypes `CreateFileMappingW`/`MapViewOfFile`/`CreateProcessW`; otherwise written to `/tmp/_ethrt_<pid>.bin`, `chmod +x`, launched via `subprocess.Popen` in a new session with the file removed after launch. The C2 URL is resolved on-chain rather than embedded as a literal, defeating static URL extraction, and the dropper functions are disguised under transaction/signing names.
## Source: kam193 (bd36aeb2d45881a66bf5373c0b91a108637938dab5e0c153525e6f938c9c9503)
A clone of a legitimate package with import-time malicious code activating if specific env variables are set. Once activated, it queries the blockchain to retrieve the next stage URL stored in a smart contract. The payload from the URL is then downloaded and executed. The address of the smart contract is not included in the package.
---
Category: MALICIOUS - The campaign has clearly malicious intent, like infostealers.
Campaign: 2026-09-web3-eth-account
Reasons (based on the campaign):
- typosquatting
- clones-real-package
- c2-in-blockchain
- Downloads and executes a remote malicious script.
The MultiVendorX WordPress plugin before 5.0.16 does not restrict who can update its role and capability settings, allowing users holding its vendor role to grant that role administrator-level capabilities and take over the site.
Improper neutralization of regular-expression metacharacters in the LINQ query translation component of the MongoDB C# Driver can cause a caller-supplied character sequence to alter a regular-expression predicate generated by an affected application. An authenticated user who can influence such a value may cause the application to return records beyond those intended by the original filter.
FileRun versions before 2026.3.0 have an OS command injection vulnerability in the PhotoProofSheet handler. Authenticated users with upload permissions can exploit this by uploading files with shell metacharacters in their names. This leads to arbitrary command execution as the web-server user due to improper sanitization in the ImageMagick montage command construction.
CVE-2026-84042 is a high-severity vulnerability in crun affecting versions 1.29 and later. When crun is built with libkrun and a container is started rootful with passt networking enabled (krun.use_passt), it allows execution of attacker-controlled payloads from the container image with host root privileges. This is a regression introduced in version 1.29 due to improper privilege management, resulting in privilege escalation to host root. Mitigation currently involves avoiding running untrusted container images with krun and passt networking until a fixed version is released.
GeoVision GV-LPC2211 V1.13 fails to restrict the filename supplied to BKDownloadLink.cgi, allowing a remote user with valid web credentials to read arbitrary files accessible to the root-run web service.