In the Linux kernel, the following vulnerability has been resolved: PM / devfreq: mtk-cci: Fix potential error pointer dereference in probe() The drv->sram_reg pointer could be set to ERR_PTR(-EPROBE_DEFER) which would lead to a error pointer dereference. Use IS_ERR_OR_NULL() to check that the pointer is valid.
In the Linux kernel, the following vulnerability has been resolved: crypto: hisilicon/qm - set NULL to qm->debug.qm_diff_regs When the initialization of qm->debug.acc_diff_reg fails, the probe process does not exit. However, after qm->debug.qm_diff_regs is freed, it is not set to NULL. This can lead to a double free when the remove process attempts to free it again. Therefore, qm->debug.qm_diff_regs should be set to NULL after it is freed.
In the Linux kernel, the following vulnerability has been resolved: media: i2c: tc358743: Fix use-after-free bugs caused by orphan timer in probe The state->timer is a cyclic timer that schedules work_i2c_poll and delayed_work_enable_hotplug, while rearming itself. Using timer_delete() fails to guarantee the timer isn't still running when destroyed, similarly cancel_delayed_work() cannot ensure delayed_work_enable_hotplug has terminated if already executing. During probe failure after timer initialization, these may continue running as orphans and reference the already-freed tc358743_state object through tc358743_irq_poll_timer. The following is the trace captured by KASAN. BUG: KASAN: slab-use-after-free in __run_timer_base.part.0+0x7d7/0x8c0 Write of size 8 at addr ffff88800ded83c8 by task swapper/1/0 ... Call Trace: <IRQ> dump_stack_lvl+0x55/0x70 print_report+0xcf/0x610 ? __pfx_sched_balance_find_src_group+0x10/0x10 ? __run_timer_base.part.0+0x7d7/0x8c0 kasan_report+0xb8/0xf0 ? __run_timer_base.part.0+0x7d7/0x8c0 __run_timer_base.part.0+0x7d7/0x8c0 ? rcu_sched_clock_irq+0xb06/0x27d0 ? __pfx___run_timer_base.part.0+0x10/0x10 ? try_to_wake_up+0xb15/0x1960 ? tmigr_update_events+0x280/0x740 ? _raw_spin_lock_irq+0x80/0xe0 ? __pfx__raw_spin_lock_irq+0x10/0x10 tmigr_handle_remote_up+0x603/0x7e0 ? __pfx_tmigr_handle_remote_up+0x10/0x10 ? sched_balance_trigger+0x98/0x9f0 ? sched_tick+0x221/0x5a0 ? _raw_spin_lock_irq+0x80/0xe0 ? __pfx__raw_spin_lock_irq+0x10/0x10 ? tick_nohz_handler+0x339/0x440 ? __pfx_tmigr_handle_remote_up+0x10/0x10 __walk_groups.isra.0+0x42/0x150 tmigr_handle_remote+0x1f4/0x2e0 ? __pfx_tmigr_handle_remote+0x10/0x10 ? ktime_get+0x60/0x140 ? lapic_next_event+0x11/0x20 ? clockevents_program_event+0x1d4/0x2a0 ? hrtimer_interrupt+0x322/0x780 handle_softirqs+0x16a/0x550 irq_exit_rcu+0xaf/0xe0 sysvec_apic_timer_interrupt+0x70/0x80 </IRQ> ... Allocated by task 141: kasan_save_stack+0x24/0x50 kasan_save_track+0x14/0x30 __kasan_kmalloc+0x7f/0x90 __kmalloc_node_track_caller_noprof+0x198/0x430 devm_kmalloc+0x7b/0x1e0 tc358743_probe+0xb7/0x610 i2c_device_probe+0x51d/0x880 really_probe+0x1ca/0x5c0 __driver_probe_device+0x248/0x310 driver_probe_device+0x44/0x120 __device_attach_driver+0x174/0x220 bus_for_each_drv+0x100/0x190 __device_attach+0x206/0x370 bus_probe_device+0x123/0x170 device_add+0xd25/0x1470 i2c_new_client_device+0x7a0/0xcd0 do_one_initcall+0x89/0x300 do_init_module+0x29d/0x7f0 load_module+0x4f48/0x69e0 init_module_from_file+0xe4/0x150 idempotent_init_module+0x320/0x670 __x64_sys_finit_module+0xbd/0x120 do_syscall_64+0xac/0x280 entry_SYSCALL_64_after_hwframe+0x77/0x7f Freed by task 141: kasan_save_stack+0x24/0x50 kasan_save_track+0x14/0x30 kasan_save_free_info+0x3a/0x60 __kasan_slab_free+0x3f/0x50 kfree+0x137/0x370 release_nodes+0xa4/0x100 devres_release_group+0x1b2/0x380 i2c_device_probe+0x694/0x880 really_probe+0x1ca/0x5c0 __driver_probe_device+0x248/0x310 driver_probe_device+0x44/0x120 __device_attach_driver+0x174/0x220 bus_for_each_drv+0x100/0x190 __device_attach+0x206/0x370 bus_probe_device+0x123/0x170 device_add+0xd25/0x1470 i2c_new_client_device+0x7a0/0xcd0 do_one_initcall+0x89/0x300 do_init_module+0x29d/0x7f0 load_module+0x4f48/0x69e0 init_module_from_file+0xe4/0x150 idempotent_init_module+0x320/0x670 __x64_sys_finit_module+0xbd/0x120 do_syscall_64+0xac/0x280 entry_SYSCALL_64_after_hwframe+0x77/0x7f ... Replace timer_delete() with timer_delete_sync() and cancel_delayed_work() with cancel_delayed_work_sync() to ensure proper termination of timer and work items before resource cleanup. This bug was initially identified through static analysis. For reproduction and testing, I created a functional emulation of the tc358743 device via a kernel module and introduced faults through the debugfs interface.
SOOP-CLM developed by PiExtract has a Server-Side Request Forgery vulnerability, allowing privileged remote attackers to read server files or probe internal network information.
In the Linux kernel, the following vulnerability has been resolved: gpiolib: acpi: initialize acpi_gpio_info struct Since commit 7c010d463372 ("gpiolib: acpi: Make sure we fill struct acpi_gpio_info"), uninitialized acpi_gpio_info struct are passed to __acpi_find_gpio() and later in the call stack info->quirks is used in acpi_populate_gpio_lookup. This breaks the i2c_hid_cpi driver: [ 58.122916] i2c_hid_acpi i2c-UNIW0001:00: HID over i2c has not been provided an Int IRQ [ 58.123097] i2c_hid_acpi i2c-UNIW0001:00: probe with driver i2c_hid_acpi failed with error -22 Fix this by initializing the acpi_gpio_info pass to __acpi_find_gpio()
In the Linux kernel, the following vulnerability has been resolved: igc: don't fail igc_probe() on LED setup error When igc_led_setup() fails, igc_probe() fails and triggers kernel panic in free_netdev() since unregister_netdev() is not called. [1] This behavior can be tested using fault-injection framework, especially the failslab feature. [2] Since LED support is not mandatory, treat LED setup failures as non-fatal and continue probe with a warning message, consequently avoiding the kernel panic. [1] kernel BUG at net/core/dev.c:12047! Oops: invalid opcode: 0000 [#1] SMP NOPTI CPU: 0 UID: 0 PID: 937 Comm: repro-igc-led-e Not tainted 6.17.0-rc4-enjuk-tnguy-00865-gc4940196ab02 #64 PREEMPT(voluntary) Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 RIP: 0010:free_netdev+0x278/0x2b0 [...] Call Trace: <TASK> igc_probe+0x370/0x910 local_pci_probe+0x3a/0x80 pci_device_probe+0xd1/0x200 [...] [2] #!/bin/bash -ex FAILSLAB_PATH=/sys/kernel/debug/failslab/ DEVICE=0000:00:05.0 START_ADDR=$(grep " igc_led_setup" /proc/kallsyms \ | awk '{printf("0x%s", $1)}') END_ADDR=$(printf "0x%x" $((START_ADDR + 0x100))) echo $START_ADDR > $FAILSLAB_PATH/require-start echo $END_ADDR > $FAILSLAB_PATH/require-end echo 1 > $FAILSLAB_PATH/times echo 100 > $FAILSLAB_PATH/probability echo N > $FAILSLAB_PATH/ignore-gfp-wait echo $DEVICE > /sys/bus/pci/drivers/igc/bind
In the Linux kernel, the following vulnerability has been resolved: iommu/s390: Make attach succeed when the device was surprise removed When a PCI device is removed with surprise hotplug, there may still be attempts to attach the device to the default domain as part of tear down via (__iommu_release_dma_ownership()), or because the removal happens during probe (__iommu_probe_device()). In both cases zpci_register_ioat() fails with a cc value indicating that the device handle is invalid. This is because the device is no longer part of the instance as far as the hypervisor is concerned. Currently this leads to an error return and s390_iommu_attach_device() fails. This triggers the WARN_ON() in __iommu_group_set_domain_nofail() because attaching to the default domain must never fail. With the device fenced by the hypervisor no DMAs to or from memory are possible and the IOMMU translations have no effect. Proceed as if the registration was successful and let the hotplug event handling clean up the device. This is similar to how devices in the error state are handled since commit 59bbf596791b ("iommu/s390: Make attach succeed even if the device is in error state") except that for removal the domain will not be registered later. This approach was also previously discussed at the link. Handle both cases, error state and removal, in a helper which checks if the error needs to be propagated or ignored. Avoid magic number condition codes by using the pre-existing, but never used, defines for PCI load/store condition codes and rename them to reflect that they apply to all PCI instructions.
In the Linux kernel, the following vulnerability has been resolved: um: virtio_uml: Fix use-after-free after put_device in probe When register_virtio_device() fails in virtio_uml_probe(), the code sets vu_dev->registered = 1 even though the device was not successfully registered. This can lead to use-after-free or other issues.
TCL 65C655 Smart TV, running firmware version V8-R75PT01-LF1V269.001116 (Android TV, Kernel 5.4.242+), is vulnerable to a blind, unauthenticated Server-Side Request Forgery (SSRF) vulnerability via the UPnP MediaRenderer service (AVTransport:1). The device accepts unauthenticated SetAVTransportURI SOAP requests over TCP/16398 and attempts to retrieve externally referenced URIs, including attacker-controlled payloads. The blind SSRF allows for sending requests on behalf of the TV, which can be leveraged to probe for other internal or external services accessible by the device (e.g., 127.0.0.1:16XXX, LAN services, or internet targets), potentially enabling additional exploit chains.
In the Linux kernel, the following vulnerability has been resolved: spi: spi-qpic-snand: unregister ECC engine on probe error and device remove The on-host hardware ECC engine remains registered both when the spi_register_controller() function returns with an error and also on device removal. Change the qcom_spi_probe() function to unregister the engine on the error path, and add the missing unregistering call to qcom_spi_remove() to avoid possible use-after-free issues.
CVE-2025-39921 is a vulnerability in the Linux kernel's spi microchip-core-qspi driver where an invalid check of op->max_freq during the supports_op callback causes a division by zero. This results in the baud_rate_val being set to INT_MAX, causing the probe of the attached memory device to fail. The issue was introduced when per-operation frequency switching support was added and was fixed by removing the invalid check to restore prior functionality.
Vasion Print (formerly PrinterLogic) Virtual Appliance Host prior to version 25.1.102 and Application prior to version 25.1.1413 (VA/SaaS deployments) contain a blind server-side request forgery (SSRF) vulnerability reachable via the /var/www/app/console_release/hp/installApp.php script that can be exploited by an unauthenticated user. When a printer is registered, the software stores the printer’s host name in the variable $printer_vo->str_host_address. The code later builds a URL like 'http://<host‑address>:80/DevMgmt/DiscoveryTree.xml' and sends the request with curl. No validation, whitelist, or private‑network filtering is performed before the request is made. Because the request is blind, an attacker cannot see the data directly, but can still: probe internal services, trigger internal actions, or gather other intelligence. This vulnerability has been confirmed to be remediated, but it is unclear as to when the patch was introduced.
Vasion Print (formerly PrinterLogic) Virtual Appliance Host prior to version 25.1.102 and Application prior to version 25.1.1413 (VA/SaaS deployments) contain a blind server-side request forgery (SSRF) vulnerability reachable via the /var/www/app/console_release/hp/log_off_single_sign_on.php script that can be exploited by an unauthenticated user. When a printer is registered, the software stores the printer’s host name in the variable $printer_vo->str_host_address. The code later builds a URL like 'http://<host‑address>:80/DevMgmt/DiscoveryTree.xml' and sends the request with curl. No validation, whitelist, or private‑network filtering is performed before the request is made. Because the request is blind, an attacker cannot see the data directly, but can still: probe internal services, trigger internal actions, or gather other intelligence. This vulnerability has been confirmed to be remediated, but it is unclear as to when the patch was introduced.
Vasion Print (formerly PrinterLogic) Virtual Appliance Host prior to version 25.1.102 and Application prior to version 25.1.1413 (VA/SaaS deployments) contain a blind server-side request forgery (SSRF) vulnerability reachable via the /var/www/app/console_release/lexmark/dellCheck.php script that can be exploited by an unauthenticated user. When a printer is registered, the software stores the printer’s host name in the variable $printer_vo->str_host_address. The code later builds a URL like 'http://<host‑address>:80/DevMgmt/DiscoveryTree.xml' and sends the request with curl. No validation, whitelist, or private‑network filtering is performed before the request is made. Because the request is blind, an attacker cannot see the data directly, but can still: probe internal services, trigger internal actions, or gather other intelligence. This vulnerability has been confirmed to be remediated, but it is unclear as to when the patch was introduced.
In the Linux kernel, the following vulnerability has been resolved: dmaengine: ti: edma: Fix memory allocation size for queue_priority_map Fix a critical memory allocation bug in edma_setup_from_hw() where queue_priority_map was allocated with insufficient memory. The code declared queue_priority_map as s8 (*)[2] (pointer to array of 2 s8), but allocated memory using sizeof(s8) instead of the correct size. This caused out-of-bounds memory writes when accessing: queue_priority_map[i][0] = i; queue_priority_map[i][1] = i; The bug manifested as kernel crashes with "Oops - undefined instruction" on ARM platforms (BeagleBoard-X15) during EDMA driver probe, as the memory corruption triggered kernel hardening features on Clang. Change the allocation to use sizeof(*queue_priority_map) which automatically gets the correct size for the 2D array structure.
Dragonfly is an open source P2P-based file distribution and image acceleration system. Versions prior to 2.1.0 contain a server-side request forgery (SSRF) vulnerability that enables users to force DragonFly2’s components to make requests to internal services that are otherwise not accessible to them. The issue arises because the Manager API accepts a user-supplied URL when creating a Preheat job with weak validation, peers can trigger other peers to fetch an arbitrary URL through pieceManager.DownloadSource, and internal HTTP clients follow redirects, allowing a request to a malicious server to be redirected to internal services. This can be used to probe or access internal HTTP endpoints. The vulnerability is fixed in version 2.1.0.
The N-Reporter, N-Cloud, and N-Probe developed by N-Partner has an OS Command Injection vulnerability, allowing authenticated remote attackers to inject arbitrary OS commands and execute them on the server.
O'View MapServer developed by PilotGaea Technologies has a Server-Side Request Forgery vulnerability, allowing unauthenticated remote attackers to exploit this vulnerability to probe internal network.