In the Linux kernel, the following vulnerability has been resolved: ALSA: virmidi: Check card index validity at probe virmidi driver blindly trusts that the given devptr->id value is within the proper card index range at probe. It's OK for the devices the driver itself creates at the module probe time, but if the device is bound manually via sysfs interface, this could be -1 as "none", and this leads to OOB access for index[] and other parameters. Add a sanity check for the card index and warn/correct it if it's a value out of the range.
In the Linux kernel, the following vulnerability has been resolved: i3c: master: adi: initialize the lock before enabling interrupts adi_i3c_master_probe() requests the IRQ and unmasks REG_IRQ_PENDING_CMDR before the controller's IBI state, transfer queue list and transfer queue lock are initialized. A pending CMDR interrupt can therefore run adi_i3c_master_irq() and take master->xferqueue.lock before the dynamic lock has been initialized. This issue was found by our static analysis tool and then manually reviewed against the current tree. The grounded PoC kept the probe ordering and the IRQ path adi_i3c_master_probe() -> adi_i3c_master_irq() -> xferqueue.lock, with a pending CMDR interrupt arriving after REG_IRQ_PENDING_CMDR is unmasked. Lockdep reported: INFO: trying to register non-static key. you didn't initialize this object before use? lock_acquire+0xbb/0x290 _raw_spin_lock_irqsave+0x36/0x60 adi_i3c_master_irq+0x32/0x56 [vuln_msv] adi_i3c_master_probe+0x5a/0xf47 [vuln_msv] Initialize the transfer queue and IBI state before requesting and unmasking the IRQ.
In the Linux kernel, the following vulnerability has been resolved: ALSA: aloop: Check card index validity at probe aloop driver blindly trusts that the given devptr->id value is within the proper card index range at probe. It's OK for the devices the driver itself creates at the module probe time, but if the device is bound manually via sysfs interface, this could be -1 as "none", and this leads to OOB access for index[] and other parameters. Add a sanity check for the card index and warn/correct it if it's a value out of the range.
In the Linux kernel, the following vulnerability has been resolved: ALSA: pcxhr: initialize mutexes before requesting threaded IRQ pcxhr_probe() requests pcxhr_threaded_irq() before initializing mgr->lock, even though the threaded handler takes that mutex. Initialize the manager locks before request_threaded_irq() so an early interrupt cannot run against uninitialized mutex state during probe.
In the Linux kernel, the following vulnerability has been resolved: ALSA: portman2x4: Check card index validity at probe Although portman2x4 driver has a check of the given devptr->id value, it doesn't check for a negative id, which is often given as "none" or such value when bound via sysfs. This may lead to OOB access for index[] and other parameters. Add a sanity check for the card index and warn/correct it if it's a value out of the range.
In the Linux kernel, the following vulnerability has been resolved: ALSA: serial-u16550: Check card index validity at probe serial-u16550 driver blindly trusts that the given devptr->id value is within the proper card index range at probe. It's OK for the devices the driver itself creates at the module probe time, but if the device is bound manually via sysfs interface, this could be -1 as "none", and this leads to OOB access for index[] and other parameters. Add a sanity check for the card index and warn/correct it if it's a value out of the range.
In the Linux kernel, the following vulnerability has been resolved: ALSA: mpu401: Check card index validity at probe mpu401 driver blindly trusts that the given devptr->id value is within the proper card index range at probe. It's OK for the devices the driver itself creates at the module probe time, but if the device is bound manually via sysfs interface, this could be -1 as "none", and this leads to OOB access for index[] and other parameters. Add a sanity check for the card index and warn/correct it if it's a value out of the range.
In the Linux kernel, the following vulnerability has been resolved: ALSA: mts64: Check card index validity at probe Although mts64 driver has a check of the given devptr->id value, it doesn't check for a negative id, which is often given as "none" or such value when bound via sysfs. This may lead to OOB access for index[] and other parameters. Add a sanity check for the card index and warn/correct it if it's a value out of the range.
In the Linux kernel, the following vulnerability has been resolved: ALSA: 6fire: bound the MIDI event length from the device usb6fire_comm_receiver_handler() forwards a MIDI event using a length byte the device supplies, with no bound and no check that the transfer delivered that many bytes: if (!urb->status) { if (rt->receiver_buffer[0] == 0x10) /* midi in event */ if (midi_rt) midi_rt->in_received(midi_rt, rt->receiver_buffer + 2, rt->receiver_buffer[1]); } receiver_buffer is a 64-byte kzalloc() buffer (COMM_RECEIVER_BUFSIZE), so only 62 bytes follow the two-byte header. receiver_buffer[1] is a u8 the device chooses, so a device that answers with 0x10 and a length of 0xFF makes snd_rawmidi_receive() read 255 bytes starting two bytes into a 64-byte object. The bytes past the buffer are handed to userspace through the rawmidi read path. urb->actual_length is not consulted either, so a short transfer leaves both the type byte and the length byte at their previous values and the handler acts on stale data. The receiver URB is submitted from usb6fire_comm_init() at probe, so the read happens on plug with no user action; forwarding to userspace also needs a MIDI input substream open, since usb6fire_midi_in_received() only calls snd_rawmidi_receive() when rt->in is set. KASAN on 7.2.0-rc5 (arm64), single packet from an emulated device: BUG: KASAN: slab-out-of-bounds in snd_rawmidi_receive Read of size 255 at addr ffff000009f64682 by task bash/183 __asan_memcpy snd_rawmidi_receive usb6fire_midi_in_received [snd_usb_6fire] usb6fire_comm_receiver_handler [snd_usb_6fire] Allocated by task 11: usb6fire_comm_init [snd_usb_6fire] usb6fire_chip_probe [snd_usb_6fire] The buggy address is located 2 bytes inside of allocated 64-byte region [ffff000009f64680, ffff000009f646c0) Reject the event when the length exceeds the bytes that follow the header, and require the transfer to have delivered the header plus that many bytes. The receiver URB is submitted with a 64-byte transfer_buffer_length, so a genuine device cannot deliver an event longer than those 62 bytes and nothing valid is dropped. Discovered by XBOW, triaged by Baul Lee <baul.lee@xbow.com>
In the Linux kernel, the following vulnerability has been resolved: net: dsa: realtek: use gpiod_set_value_cansleep for reset GPIO rtl83xx_reset_assert() and rtl83xx_reset_deassert() are only called from the probe path, which may sleep and is not timing-critical. When the reset GPIO is provided by a sleeping controller such as an I2C I/O expander, gpiod_set_value() warns: WARNING: drivers/gpio/gpiolib.c:4030 at gpiod_set_value+0x44/0x80, CPU#1: kworker/u16:4/61 Hardware name: B&O MAP CA33 Rev f (UNKNOWN) (DT) Workqueue: events_unbound deferred_probe_work_func pc : gpiod_set_value+0x44/0x80 lr : rtl83xx_probe+0x1d8/0x3a0 Call trace: gpiod_set_value+0x44/0x80 (P) rtl83xx_probe+0x1d8/0x3a0 realtek_mdio_probe+0x24/0xa0 mdio_probe+0x38/0x78 really_probe+0xc4/0x3e0 __driver_probe_device+0x15c/0x1b8 driver_probe_device+0xb4/0x120 __device_attach_driver+0xb8/0x1a0 bus_for_each_drv+0x88/0xf0 __device_attach+0xa0/0x1d8 device_initial_probe+0x54/0x68 bus_probe_device+0x38/0xa0 deferred_probe_work_func+0xb8/0x120 process_one_work+0x184/0x4e8 worker_thread+0x188/0x308 kthread+0x130/0x150 ret_from_fork+0x10/0x20 Switch both helpers to gpiod_set_value_cansleep() so such a reset GPIO can be used without triggering the warning. The reset GPIO has been driven with the non-sleeping gpiod_set_value() since the driver was added in v4.19. The call has since been refactored across several files - from realtek-smi.c / realtek-mdio.c into the common rtl83xx.c module and then into the rtl83xx_reset_assert() and rtl83xx_reset_deassert() helpers (both in v6.9). This patch therefore applies as-is only to kernels that carry those helpers (v6.9+); older stable kernels need the same gpiod_set_value_cansleep() conversion at the corresponding open-coded call sites.
In the Linux kernel, the following vulnerability has been resolved: mmc: via-sdmmc: stop card-detect handling on probe failure request_irq() registers the SD card-detect interrupt and the probe enables it before mmc_add_host() runs. If mmc_add_host() fails, the error path only unmaps the registers and returns: the interrupt stays registered, so the handler keeps running against the host once it is freed. via_sdc_isr() dereferences sdhost and its MMIO base and schedules carddet_work, which via_sdc_card_detect() also runs against freed memory through its container_of() dereference. Add a probe-error path that disables and frees the interrupt and cancels carddet_work before unmapping. carddet_work can re-enable the device interrupt via via_reset_pcictrl(), which restores PCIINTCTRL, so mask it again after cancelling the work. This issue was found by an in-house static analysis tool and confirmed by manual code review.
In the Linux kernel, the following vulnerability has been resolved: PCI: plda: Fix use-after-free of event IRQs during teardown plda_pcie_irq_domain_deinit() removes pcie->event_domain via irq_domain_remove(), but the per-event IRQs mapped from that domain are requested with devm_request_irq() in plda_init_interrupts(). The actual free_irq() for a devm-managed IRQ is deferred by devres until after the calling probe()/remove() function returns. This means irq_domain_remove() can free the domain's internal data before the deferred free_irq() for IRQs still mapped into it has run. When devres later processes that deferred cleanup, it can end up dereferencing the already-freed domain. Free each event IRQ explicitly with devm_free_irq() before removing the domain. This triggers the free immediately and removes the IRQ from the devres tracking list, so devres will not attempt to free it a second time later. Also dispose of the event, INTx, and MSI IRQ mappings with irq_dispose_mapping() before their owning domains are removed. Finally, guard the calls to irq_set_chained_handler_and_data() for pcie->irq, pcie->msi_irq, and pcie->intx_irq so they only run when those fields hold a valid (>0) IRQ number. This is a pre-existing issue, flagged by automated review during work on an earlier, unrelated patch to this driver. Build-tested and boot-tested on StarFive VisionFive v1.2A board
In the Linux kernel, the following vulnerability has been resolved: power: supply: bq25890: Fix power_supply reference leak bq25890_fw_probe() acquires a reference to a secondary charger using power_supply_get_by_name(), but the reference is not released on later probe failures or on driver detach. In particular, failures after bq25890_fw_probe() returns successfully, such as a failure in bq25890_hw_init(), also leak the reference. Register a device-managed cleanup action immediately after acquiring the secondary charger. This releases the reference on all subsequent probe failures and on driver detach. Found by code review.
In the Linux kernel, the following vulnerability has been resolved: power: supply: rt9455: quiesce delayed work before teardown The threaded IRQ handler can queue pwr_rdy_work, max_charging_time_work and batt_presence_work. pwr_rdy_work and batt_presence_work can also queue max_charging_time_work, while batt_presence_work can requeue itself. rt9455_remove() cancels max_charging_time_work before batt_presence_work. The latter can therefore queue max_charging_time_work after it has already been cancelled: rt9455_remove() workqueue cancel pwr_rdy_work cancel max_charging_time_work batt_presence_work queues max_charging_time_work cancel batt_presence_work return devres frees rt9455_info max_charging_time_work dereferences rt9455_info The IRQ also remains registered until devres cleanup and can queue more work after any of the cancellation calls. If rt9455_hw_init() fails after the IRQ has been requested, probe returns without cancelling work that may already have been queued. A pending callback can then access rt9455_info after it has been freed. Register rt9455_cancel_all_delayed_works() through devm_add_action_or_reset() right after devm_power_supply_register(). devres invokes the action in reverse registration order, after the managed IRQ has been freed and before rt9455_info is released, so the delayed works are drained in both rt9455_remove() and the probe error path. Cancel pwr_rdy_work and batt_presence_work before max_charging_time_work because both can queue the latter. This issue was found by an in-house static analysis tool.
In the Linux kernel, the following vulnerability has been resolved: power: supply: cros_usbpd: Limit port counts to EC_USB_PD_MAX_PORTS Currently the cros_usbpd-charger driver probe iterates based on raw charger port count returned by the embedded controller. The only check is against the number of USB PD ports which the embedded controller also defines. A malicious embedded controller could return an inaccurate port count (up to 255) resulting in an out of bounds write and subsequent memory corruption. Update helper functions in cros_usbpd-charger to limit port counts to EC_USB_PD_MAX_PORTS.
A use-after-free vulnerability in the Linux kernel's HID driver for the mcp2221 device has been resolved. The issue involved device IO not being properly stopped before hardware teardown during probe failure or device removal, which could lead to a race condition. The fix ensures device IO is quiesced at the start of the cleanup callback and guards the call to stop device IO to avoid spurious warnings. This vulnerability affects specific Linux kernel versions listed and is rated medium severity.
In the Linux kernel, the following vulnerability has been resolved: wifi: rtw88: pci: fix resource leak on failed NAPI setup rtw_pci_probe() allocates PCI resources through rtw_pci_setup_resource() before it sets up NAPI. If rtw_pci_napi_init() fails, the error path jumps straight to err_pci_declaim and skips rtw_pci_destroy(), leaving the PCI resources allocated by rtw_pci_setup_resource() behind. Add a dedicated cleanup label for the NAPI setup failure path so probe destroys the PCI resources. The bug was first flagged by an experimental analysis tool we are developing for kernel memory-management bugs while analyzing current mainline kernels. The tool is still under development and is not yet publicly available. Manual inspection confirms that the bug is still present in v7.1-rc7. An x86_64 allyesconfig build showed no new warnings. As we do not have a suitable rtw88 PCI board to test with, no runtime testing was able to be performed.
CVE-2026-89738 is a use-after-free vulnerability in the Linux kernel's at91_udc USB gadget driver. It occurs because a polled-VBUS timer and associated work are not properly drained before the USB device controller (udc) is freed during driver removal or probe failure. This can lead to dereferencing freed memory, causing potential system crashes or escalation of privileges. The issue affects Linux kernel version 2.6.36 and has been fixed in subsequent commits.